View STGB10NC60HDT4_4924247.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

STGB10NC60HD - STGD10NC60HD STGF10NC60HD - STGP10NC60HD
600 V - 10 A - very fast IGBT
Features

Low on-voltage drop (VCE(sat)) Low CRES / CIES ratio (no cross-conduction susceptibility) Very soft ultra fast recovery antiparallel diode
3 1
2 3 1
DPAK
DPAK
Applications

High frequency motor controls
3
SMPS and PFC in both hard switch and resonant topologies Motor drivers
1
2
3 1 2
TO-220FP
TO-220
Description
This IGBT utilizes the advanced PowerMESHTM process resulting in an excellent trade-off between switching performance and low on-state behavior.
Figure 1.
Internal schematic diagram
Table 1.
Device summary
Marking GB10NC60HD GD10NC60HD GF10NC60HD GP10NC60HD Package DPAK Tape and reel DPAK TO-220FP Tube TO-220 Packaging
Order codes STGB10NC60HDT4 STGD10NC60HDT4 STGF10NC60HD STGP10NC60HD
December 2008
Rev 5
1/19
www.st.com 19
Contents
STGB10NC60HD, STGD10NC60HD, STGF10NC60HD, STGP10NC60HD
Contents
1 2 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2.1 Electrical characteristics (curves) ............................. 7
3 4
Test circuit
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4.1 Packaging mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
2/19
STGB10NC60HD, STGD10NC60HD, STGF10NC60HD, STGP10NC60HD
Electrical ratings
1
Electrical ratings
Table 2.
Symbol
Absolute maximum ratings
Value Parameter TO-220 / DPAK Unit DPAK 600 20 10 30 30 20 10 20 65 62 24 2500 - 55 to 150 9 6 TO-220FP V A A A A V A A W V C
VCES IC(1) IC(1) ICL(2) ICP(3) VGE IF IFSM PTOT VISO TJ
Collector-emitter voltage (VGE = 0) Collector current (continuous) at TC = 25 C Collector current (continuous) at TC = 100 C Turn-off latching current Pulsed collector current Gate-emitter voltage Diode RMS forward current at TC = 25 C Surge not repetitive forward current tp = 10 ms sinusoidal Total dissipation at TC = 25 C Insulation withstand voltage (RMS) from all three leads to external heat sink (t = 1 s; TC = 25 C) Operating junction temperature
1. Calculated according to the iterative formula:
T j ( max ) - T C I C ( T C ) = ------------------------------------------------------------------------------------------------------R thj - c x V CE ( sat ) ( max ) ( T j ( max ), I C ( T C ) )
2. Vclamp = 80 % (VCES), VGE = 15 V, RG = 10 , TJ = 150 C 3. Pulse width limited by max junction temperature allowed
Table 3.
Thermal resistance
Value
Symbol
Parameter
DPAK TO-220
Unit DPAK 2.0 4.5 100 TO-220FP 5.1 7 62.5 C/W C/W C/W
Rthj-case Thermal resistance junction-case IGBT max. Rthj-case Thermal resistance junction-case diode max. Rthj-amb Thermal resistance junction-ambient max.
1.9 4 62.5
3/19
Electrical characteristics
STGB10NC60HD, STGD10NC60HD, STGF10NC60HD, STGP10NC60HD
2
Electrical characteristics
(TCASE = 25 C unless otherwise specified) Table 4.
Symbol
Static
Parameter Test conditions Min. Typ. Max. Unit
Collector-emitter V(BR)CES breakdown voltage (VGE= 0) VCE(sat) VGE(th) ICES IGES gfs (1)
IC= 1 mA
600 1.9 1.7 3.75 5.75 150 1 100 3.5 2.5
V V V V A mA nA S
VGE = 15 V, IC = 5 A Collector-emitter saturation VGE = 15 V, IC = 5 A, voltage TC = 125 C Gate threshold voltage Collector cut-off current (VGE = 0) Gate-emitter leakage current (VCE = 0) Forward transconductance VCE= VGE, IC= 250 A VCE = 600 V VCE = 600 V, TC = 125 C VGE = 20 V VCE = 15 V, IC= 5 A
1. Pulse duration = 300 s, duty cycle 1.5 %
Table 5.
Symbol Cies Coes Cres Qg Qge Qgc
Dynamic
Parameter Input capacitance Output capacitance Reverse transfer capacitance Total gate charge Gate-emitter charge Gate-collector charge Test conditions Min. Typ. 365 43 8.3 Max. Unit pF pF pF
VCE = 25 V, f = 1 MHz, VGE = 0
VCE = 390 V, IC = 5 A, VGE = 15 V (see Figure 19)
19.2 4.5 7
nC nC nC
4/19
STGB10NC60HD, STGD10NC60HD, STGF10NC60HD, STGP10NC60HD
Electrical characteristics
Table 6.
Symbol td(on) tr (di/dt)on
Switching on/off (inductive load)
Parameter Turn-on delay time Current rise time Turn-on current slope Test conditions VCC = 390 V, IC = 5 A RG= 10 , VGE= 15 V, (see Figure 18) (see Figure 20) VCC = 390 V, IC = 5 A RG= 10 , VGE= 15 V, TC = 125 C (see Figure 18) (see Figure 20) Vcc = 390 V, IC = 5 A, RGE = 10 , VGE = 15 V (see Figure 18) (see Figure 20) Vcc = 390 V, IC = 5 A, RGE=10 , VGE =15 V, TC = 125 C (see Figure 18) (see Figure 20) Min. Typ. 14.2 5 1000 Max. Unit ns ns A/s
td(on) tr (di/dt)on
Turn-on delay time Current rise time Turn-on current slope
14 5 920
ns ns A/s
tr(Voff) td(off) tf
Off voltage rise time Turn-off delay time Current fall time
27 72 85
ns ns ns
tr(Voff) td(off) tf
Off voltage rise time Turn-off delay time Current fall time
50 108 139
ns ns ns
Table 7.
Symbol Eon(1) Eoff(2) Ets Eon(1) Eoff(2) Ets
Switching energy (inductive load)
Parameter Turn-on switching losses Turn-off switching losses Total switching losses Test conditions VCC = 390 V, IC = 5 A RG= 10 , VGE = 15 V, (see Figure 18) VCC = 390 V, IC = 5 A RG= 10 , VGE = 15 V, TC = 125 C (see Figure 18) Min. Typ. 31.8 95 126.8 Max. Unit J J J
Turn-on switching losses Turn-off switching losses Total switching losses
61.8 173 234.8
J J J
1. Eon is the turn-on losses when a typical diode is used in the test circuit in Figure 18. If the IGBT is offered in a package with a co-pak diode, the co-pack diode is used as external diode. IGBTs & Diode are at the same temperature (25 C and 125 C) 2. Turn-off losses include also the tail of the collector current
5/19
Electrical characteristics
STGB10NC60HD, STGD10NC60HD, STGF10NC60HD, STGP10NC60HD
Table 8.
Symbol VF trr Qrr Irrm trr Qrr Irrm
Collector-emitter diode
Parameter Forward on-voltage Reverse recovery time Reverse recovery charge Reverse recovery current Reverse recovery time Reverse recovery charge Reverse recovery current Test conditions IF = 5 A IF = 5 A, TC = 125 C IF = 5 A, VR = 40 V, di/dt = 100 A/s (see Figure 21) IF = 5 A,VR = 40 V, TC =125 C, di/dt = 100 A/s (see Figure 21) Min. Typ. 2 1.7 22 14 1.3 33 30 1.85 Max. 2.45 Unit V V ns nC A ns nC A
6/19
STGB10NC60HD, STGD10NC60HD, STGF10NC60HD, STGP10NC60HD
Electrical characteristics
2.1
Figure 2.
Electrical characteristics (curves)
Output characteristics Figure 3. Transfer characteristics
Figure 4.
Transconductance
Figure 5.
Collector-emitter on voltage vs temperature
Figure 6.
Gate charge vs gate-source voltage Figure 7.
Capacitance variations
7/19
Electrical characteristics Figure 8.
STGB10NC60HD, STGD10NC60HD, STGF10NC60HD, STGP10NC60HD Figure 9. Collector-emitter on voltage vs collector current
Normalized gate threshold voltage vs temperature
Figure 10. Normalized breakdown voltage vs temperature
Figure 11. Switching losses vs temperature
Figure 12. Switching losses vs gate resistance Figure 13. Switching losses vs collector current
8/19
STGB10NC60HD, STGD10NC60HD, STGF10NC60HD, STGP10NC60HD Figure 14. Thermal impedance for TO-220 / DPAK / DPAK
Electrical characteristics
Figure 15. Turn-off SOA
Figure 16. Thermal impedance for TO-220FP Figure 17. Emitter-collector diode characteristics
IFM(A)
15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0
Tj=125C (maximum values) Tj=25C (maximum values) Tj=125C (typical values)
VFM(V)
1 2 3 4 5
9/19
Test circuit
STGB10NC60HD, STGD10NC60HD, STGF10NC60HD, STGP10NC60HD
3
Test circuit
Figure 19. Gate charge test circuit
Figure 18. Test circuit for inductive load switching
Figure 20. Switching waveform
Figure 21. Diode recovery time waveform
10/19
STGB10NC60HD, STGD10NC60HD, STGF10NC60HD, STGP10NC60HD Package mechanical data
4
Package mechanical data
In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK(R) packages, depending on their level of environmental compliance. ECOPACK(R) specifications, grade definitions and product status are available at: www.st.com. ECOPACK(R) is an ST trademark.
11/19
Package mechanical data STGB10NC60HD, STGD10NC60HD, STGF10NC60HD, STGP10NC60HD
DPAK (TO-263) mechanical data
mm Dim Min A A1 b b2 c c2 D D1 E E1 e e1 H J1 L L1 L2 R V2 4.40 0.03 0.70 1.14 0.45 1.23 8.95 7.50 10 8.50 2.54 4.88 15 2.49 2.29 1.27 1.30 0.4 0 8 0 5.28 15.85 2.69 2.79 1.40 1.75 0.192 0.590 0.099 0.090 0.05 0.051 Typ Max 4.60 0.23 0.93 1.70 0.60 1.36 9.35 10.40 Min 0.173 0.001 0.027 0.045 0.017 0.048 0.352 0.295 0.394 0.334
inch Typ Max 0.181 0.009 0.037 0.067 0.024 0.053 0.368 0.409 0.1 0.208 0.624 0.106 0.110 0.055 0.069 0.016 8
0079457_M
12/19
STGB10NC60HD, STGD10NC60HD, STGF10NC60HD, STGP10NC60HD Package mechanical data
TO-252 (DPAK) mechanical data
DIM. A A1 A2 b b4 c c2 D D1 E E1 e e1 H L L1 L2 L4 R V2 0o 0.60 0.20 8o 4.40 9.35 1 2.80 0.80 1 6.40 4.70 2.28 4.60 10.10 mm. min. 2.20 0.90 0.03 0.64 5.20 0.45 0.48 6.00 5.10 6.60 typ max. 2.40 1.10 0.23 0.90 5.40 0.60 0.60 6.20
0068772_G
13/19
Package mechanical data STGB10NC60HD, STGD10NC60HD, STGF10NC60HD, STGP10NC60HD
TO-220FP mechanical data mm Dim. Min.
A B D E F F1 F2 G G1 H L2 L3 L4 L5 L6 L7 Dia 28.6 9.8 2.9 15.9 9 3 4.4 2.5 2.5 0.45 0.75 1.15 1.15 4.95 2.4 10 16 30.6 10.6 3.6 16.4 9.3 3.2
Typ.
Max.
4.6 2.7 2.75 0.7 1 1.70 1.5 5.2 2.7 10.4
L7 E A
B Dia L6 L5 F1 F2 F D
H G1
G
L2 L 3
L4 7012510_Rev_J
14/19
STGB10NC60HD, STGD10NC60HD, STGF10NC60HD, STGP10NC60HD Package mechanical data
TO-220 mechanical data
mm Dim Min A b b1 c D D1 E e e1 F H1 J1 L L1 L20 L30 P Q 4.40 0.61 1.14 0.48 15.25 1.27 10 2.40 4.95 1.23 6.20 2.40 13 3.50 16.40 28.90 3.75 2.65 3.85 2.95 0.147 0.104 10.40 2.70 5.15 1.32 6.60 2.72 14 3.93 0.393 0.094 0.194 0.048 0.244 0.094 0.511 0.137 Typ Max 4.60 0.88 1.70 0.70 15.75 Min 0.173 0.024 0.044 0.019 0.6
inch Typ Max 0.181 0.034 0.066 0.027 0.62 0.050 0.409 0.106 0.202 0.051 0.256 0.107 0.551 0.154 0.645 1.137 0.151 0.116
15/19
Package mechanical data STGB10NC60HD, STGD10NC60HD, STGF10NC60HD, STGP10NC60HD
4.1
Packaging mechanical data
D2PAK FOOTPRINT
TAPE AND REEL SHIPMENT
REEL MECHANICAL DATA
DIM. A B C D G N T 1.5 12.8 20.2 24.4 100 30.4 26.4 13.2 mm MIN. MAX. 330 0.059 0.504 0.520 0795 0.960 1.039 3.937 1.197 BULK QTY 1000 inch MIN. MAX. 12.992
TAPE MECHANICAL DATA
DIM. A0 B0 D D1 E F K0 P0 P1 P2 R T W mm MIN. 10.5 15.7 1.5 1.59 1.65 11.4 4.8 3.9 11.9 1.9 50 0.25 23.7 24.3 MAX. 10.7 15.9 1.6 1.61 1.85 11.6 5.0 4.1 12.1 2.1 inch MIN. MAX. 0.413 0.421 0.618 0.626 0.059 0.063 0.062 0.063 0.065 0.073 0.449 0.456 0.189 0.197 0.153 0.161 0.468 0.476 0.075 0.082 1.574 0.35 0.0098 0.0137 0.933 0.956
BASE QTY 1000
* on sales type
16/19
STGB10NC60HD, STGD10NC60HD, STGF10NC60HD, STGP10NC60HD Package mechanical data
DPAK FOOTPRINT
All dimensions are in millimeters
TAPE AND REEL SHIPMENT
REEL MECHANICAL DATA
DIM. A B C D G N T 1.5 12.8 20.2 16.4 50 22.4 18.4 13.2 mm MIN. MAX. 330 0.059 0.504 0.520 0.795 0.645 0.724 1.968 0.881 BULK QTY 2500 inch MIN. MAX. 12.992
TAPE MECHANICAL DATA
DIM. A0 B0 B1 D D1 E F K0 P0 P1 P2 R
W
BASE QTY 2500
mm MIN. 6.8 10.4 1.5 1.5 1.65 7.4 2.55 3.9 7.9 1.9 40
15.7 16.3
inch MIN. MAX. 7 0.267 0.275 0.409 0.417 0.476 0.059 0.063 0.059 0.065 0.073 0.291 0.299 0.100 0.108 0.153 0.161 0.311 0.319 0.075 0.082 1.574
0.618 0.641
MAX. 10.6 12.1 1.6 1.85 7.6 2.75 4.1 8.1 2.1
17/19
Revision history
STGB10NC60HD, STGD10NC60HD, STGF10NC60HD, STGP10NC60HD
5
Revision history
Table 9.
Date 30-Jan-2006 06-Nov-2006 08-Feb-2007 05-Oct-2007 16-Dec-2008
Document revision history
Revision 1 2 3 4 5 Initial release Complete version The document has been reformatted Added TO-220FP, Table 2 has been updated Added DPAK package Changes
18/19
STGB10NC60HD, STGD10NC60HD, STGF10NC60HD, STGP10NC60HD
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries ("ST") reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST's terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST'S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER'S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
(c) 2008 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com
19/19

▲Up To Search▲

Price & Availability of STGB10NC60HDT4

	To Download STGB10NC60HDT4 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .